Mirrors/knx
1
0
Fork 0
mirror of https://github.com/thelsing/knx.git synced 2026-03-07 02:17:30 +01:00
Code Issues Packages Projects Releases Wiki Activity

change last pull request a bit

Browse Source
This commit is contained in:
Thomas Kunze
2019-05-27 21:41:04 +02:00
parent 2636510bb1
commit 0628d88921
6 changed files with 92 additions and 205 deletions
Download Patch File Download Diff File Expand all files Collapse all files

50
examples/knx-demo/knx-demo.ino
View File

@@ -17,7 +17,6 @@ long lastsend = 0;
void measureTemp()
{
long now = millis();
if ((now - lastsend) < 2000)
return;
@@ -58,11 +57,11 @@ void setup()
SerialDBG.begin(115200);
randomSeed(millis());
#ifdef ARDUINO_ARCH_ESP8266
WiFiManager wifiManager;
#ifdef ARDUINO_ARCH_ESP8266
WiFiManager wifiManager;
wifiManager.autoConnect("knx-demo");
#endif
#endif
// read adress table, association table, groupobject table and parameters from eeprom
knx.readMemory();
@@ -72,30 +71,31 @@ void setup()
{
// register callback for reset GO
goReset.callback(resetCallback);
SerialDBG.print("Timeout: "); SerialDBG.println(knx.paramByte(0));
SerialDBG.print("Zykl. senden: "); SerialDBG.println(knx.paramByte(1));
SerialDBG.print("Min/Max senden: "); SerialDBG.println(knx.paramByte(2));
SerialDBG.print("Aenderung senden: "); SerialDBG.println(knx.paramByte(3));
SerialDBG.print("Abgleich: "); SerialDBG.println(knx.paramByte(4));
}
#ifdef ARDUINO_ARCH_ESP8266
// GPIO (?) of the ESP8266, in which case this is determined by the board selection
knx.ledPin(LED_BUILTIN);
// GPIO (?) of the ESP8266, the value depends on the circuit used on the board of the led
// if "0" or "low" then the output switches to gnd, at "1" or "high" the output switches to vcc
// if the next line is commented out then the default is: output switches to gnd
//knx.ledPinActiveOn(HIGH);
// GPIO (14) of the ESP8266, in which case it is the connector pin D5 on WeMos D1 R2
knx.buttonPin(14);
#endif
// start the framework. Will get wifi first.
SerialDBG.print("Timeout: ");
SerialDBG.println(knx.paramByte(0));
SerialDBG.print("Zykl. senden: ");
SerialDBG.println(knx.paramByte(1));
SerialDBG.print("Min/Max senden: ");
SerialDBG.println(knx.paramByte(2));
SerialDBG.print("Aenderung senden: ");
SerialDBG.println(knx.paramByte(3));
SerialDBG.print("Abgleich: ");
SerialDBG.println(knx.paramByte(4));
}
// pin or GPIO the programming led is connected to. Default is LED_BUILDIN
// knx.ledPin(LED_BUILTIN);
// is the led active on HIGH or low? Default is LOW
// knx.ledPinActiveOn(HIGH);
// pin or GPIO programming button is connected to. Default is 0
// knx.buttonPin(0);
// start the framework.
knx.start();
}
void loop()
void loop()
{
// don't delay here to much. Otherwise you might lose packages or mess up the timing with ETS
knx.loop();